Passive PoE Injector Cable Set : ID 435 : $5.95 : Adafruit
Par un écrivain mystérieux
Last updated 23 mai 2024
Adafruit Industries, Unique & fun DIY electronics and kits Passive PoE Injector Cable Set : ID 435 - Simplify your Internet of Things with a passive PoE injector cable. These are quite handy for projects that have Ethernet connectivity and also need a power cable. Of course, you can get a long Ethernet cable but then you have to figure out how to plug it in, making a
Simplify your Internet of Things with a passive PoE injector cable. These are quite handy for projects that have Ethernet connectivity and also need a power cable. Of course, you can get a long Ethernet cable but then you have to figure out how to plug it in, making a mess of wires. There is an official Power-over-Ethernet standard that allows devices and routers to activate a 48VDC power line on the unused Ethernet pins (4,5 and 7,8) but PoE is expensive, requiring a special router and then a step-down converter to handle the high 48V lineFor DIY projects, you may want to consider using these cables instead. One cable (the injector half) has a Ethernet plug and port and a 2.1mm jack. When you plug in a power supply (say a 9VDC wall adapter), the injector merges the power adapter in so that pins 4 and 5 connect to the power adapter power and pins 7 and 8 have the ground signal. This is also known as "Mode B" compatibility The other cable (the extractor half) does the opposite, splitting off pins 4,5 and 7,8 and bringing them to a 2.1mm DC barrel plug. You can then use the DC plug to power your projects as if it was connected directly to the wall adapter.These are NOT official/standard "Power Over Ethernet" cables and you cannot use these to provide power to an Arduino or other products from an official PoE host device (which will supply 48VDC). They must be used a pair!Note that Ethernet cables, especially long ones, will act like resistors as you get past 10 meter spans. Most Ethernet cables are 24AWG, 0.085 ohms per meter (0.026 ohms per foot) so if you want to draw say 500mA from your adapter, there will be a 1 Volt drop for every ~25 meters / 80 feet.Because these cables use pins 4,5,7, and 8 to pass power you can't use these in gigabit Ethernet situations (those pins would be used by the gigabit router), but your device and router should back down to 10/100 megabit in such cases.
Simplify your Internet of Things with a passive PoE injector cable. These are quite handy for projects that have Ethernet connectivity and also need a power cable. Of course, you can get a long Ethernet cable but then you have to figure out how to plug it in, making a mess of wires. There is an official Power-over-Ethernet standard that allows devices and routers to activate a 48VDC power line on the unused Ethernet pins (4,5 and 7,8) but PoE is expensive, requiring a special router and then a step-down converter to handle the high 48V lineFor DIY projects, you may want to consider using these cables instead. One cable (the injector half) has a Ethernet plug and port and a 2.1mm jack. When you plug in a power supply (say a 9VDC wall adapter), the injector merges the power adapter in so that pins 4 and 5 connect to the power adapter power and pins 7 and 8 have the ground signal. This is also known as "Mode B" compatibility The other cable (the extractor half) does the opposite, splitting off pins 4,5 and 7,8 and bringing them to a 2.1mm DC barrel plug. You can then use the DC plug to power your projects as if it was connected directly to the wall adapter.These are NOT official/standard "Power Over Ethernet" cables and you cannot use these to provide power to an Arduino or other products from an official PoE host device (which will supply 48VDC). They must be used a pair!Note that Ethernet cables, especially long ones, will act like resistors as you get past 10 meter spans. Most Ethernet cables are 24AWG, 0.085 ohms per meter (0.026 ohms per foot) so if you want to draw say 500mA from your adapter, there will be a 1 Volt drop for every ~25 meters / 80 feet.Because these cables use pins 4,5,7, and 8 to pass power you can't use these in gigabit Ethernet situations (those pins would be used by the gigabit router), but your device and router should back down to 10/100 megabit in such cases.
Power over Ethernet (PoE) splitters can make your project wiring a breeze - and best of all they work to connect any 802.3af-capable router to any Ethernet device, even if it doesn't natively support PoE! The splitter takes a unified PoE signal (data and power) from one cable, and then separates the data (Ethernet) and power (+12VDC regulated) into two different lines for non-PoE devices.
adafruit-802.3af PoE Output Data & Power Splitter - 5/9/12V ADA3239
5 Pairs Passive PoE Injector and PoE Splitter Kit with
5V 1.8A Isolated Output PoE Module - For Raspberry Pi 3 B+ or 4
NetDirect - Serial to Power Over Ethernet (PoE) Cable: DCE (female)
Power over Ethernet (PoE) splitters can make your project wiring a breeze - and best of all they work to connect any 802.3af-capable router to any Ethernet device, even if it doesn't natively support PoE! The splitter takes a unified PoE signal (data and power) from one RJ-45 cable, and then separates the data (Ethernet) and power (5 VDC regulated) into two different lines for non-PoE devices.
adafruit-PoE Splitter with MicroUSB Plug - Isolated 12W - 5V 2.4 Amp
Power over Ethernet (PoE) splitters can make your project wiring a breeze - and best of all they work to connect any 802.3af-capable router to any Ethernet device, even if it doesn't natively support PoE! The splitter takes a unified PoE signal (data and power) from one RJ-45 cable, and then separates the data (Ethernet) and power (5 VDC regulated) into two different lines for non-PoE devices.
adafruit-PoE Splitter with MicroUSB Plug - Isolated 12W - 5V 2.4 Amp
PoE Splitter with MicroUSB Plug - Isolated 12W - 5V 2.4 Amp : ID
adafruit-PoE Splitter with USB Type C - 5V 2A - 100 MB Ethernet
Power over Ethernet (PoE) splitters can make your project wiring a breeze - and best of all they work to connect any 802.3af-capable router to any
PoE Splitter with MicroUSB Plug - Isolated 12W - 5V 2.4 Amp
DSLRKIT Gigabit USB Type C Active PoE Splitter 48V to
Recommandé pour vous
- Gigabit Power over Ethernet (PoE) Injector 802.3af - Pronto Networks14 Jul 2023
- PoE Injector vs PoE Splitter14 Jul 2023
- Power Over Ethernet Injector14 Jul 2023
- GigE Passive PoE Injector14 Jul 2023
- Passive PoE Injector 24VDC14 Jul 2023
- GigE Passive PoE Injector14 Jul 2023
- PoE Injectors Collection – DCAmericas14 Jul 2023
- How to Use a PoE Injector to Install an IP Camera (In 3 Simple Steps)14 Jul 2023
- EDIMAX - Conmutadores - PoE Injector - Inyector PoE+ Gigabit IEEE14 Jul 2023
- 30W Gigabit Single Port Power Over Ethernet PoE Injector, 802.3at14 Jul 2023
Tu pourrais aussi aimer
- Bache imperméable etm® avec oeillet, Bache de protection extérieur & intérieur, Bache étanche & résistante à l'eau et UV, Epaisse densité 140g/m²14 Jul 2023
- Montpellier : un enseignant tague des voitures de pompiers et de police14 Jul 2023
- Ravensburger Globe pour enfants illuminé (Francais) - 187 pièces14 Jul 2023
- Élingue chaîne à rouleaux - Anneaux mâle ou femelle - Cablac14 Jul 2023
- 5 Ways To Add Navigation to Your Older Car14 Jul 2023
- Gifi Algérie - Support de poche à douille pour vous14 Jul 2023
- Tronçonneuse thermique MS 362 C-M - Stihl - Guide Rollo E - 50 cm (3/8 36RS) Stihl14 Jul 2023
- Cuillères gourmandes facile et rapide : découvrez les recettes de Cuisine Actuelle14 Jul 2023
- FIXER SA MONTRE GARMIN FENIX 6, TACTIX, QUATIX SUR SON CINTRE DE VÉLO14 Jul 2023
- Recharge de ruban noir pour étiqueteuse14 Jul 2023