Accueil jayo petg

Is petg notoriously stringy and horrible for small models? I just got my ender 3 V2 for Christmas and a jayo petg roll. I had horrible luck getting this to print at

Par un écrivain mystérieux
Last updated 11 mai 2024
Is petg notoriously stringy and horrible for small models? I just got my ender 3 V2 for Christmas and a jayo petg roll. I had horrible luck getting this to print at
Is petg notoriously stringy and horrible for small models? I just got my ender 3 V2 for Christmas and a jayo petg roll. I had horrible luck getting this to print at
PETG Stringing: 3 Simple Solutions
Is petg notoriously stringy and horrible for small models? I just got my ender 3 V2 for Christmas and a jayo petg roll. I had horrible luck getting this to print at
Poor adhesion - Ender 3 V2 PETG : r/FixMyPrint
Is petg notoriously stringy and horrible for small models? I just got my ender 3 V2 for Christmas and a jayo petg roll. I had horrible luck getting this to print at
How come PETG Prusament prints best at 220°C, when recommended is 250°C? : r/prusa3d
Is petg notoriously stringy and horrible for small models? I just got my ender 3 V2 for Christmas and a jayo petg roll. I had horrible luck getting this to print at
PETG Stringing: 3 Simple Solutions
Is petg notoriously stringy and horrible for small models? I just got my ender 3 V2 for Christmas and a jayo petg roll. I had horrible luck getting this to print at
PETG print looks bad and shows stringing – Assembly and first prints troubleshooting – Prusa3D Forum
Is petg notoriously stringy and horrible for small models? I just got my ender 3 V2 for Christmas and a jayo petg roll. I had horrible luck getting this to print at
PETG Stringing: 3 Simple Solutions
Is petg notoriously stringy and horrible for small models? I just got my ender 3 V2 for Christmas and a jayo petg roll. I had horrible luck getting this to print at
What causes these stringing in PETG filament even after fine tuning settings? #3dprinting
Is petg notoriously stringy and horrible for small models? I just got my ender 3 V2 for Christmas and a jayo petg roll. I had horrible luck getting this to print at
Too much heat? Not enough? Heat transfer paper 196° on 100% cotton shirt. Shirt peeling after first wash. Cold wash normal dry as per instructions. Front of shirt same process 0 issue. : r/SCREENPRINTING
Is petg notoriously stringy and horrible for small models? I just got my ender 3 V2 for Christmas and a jayo petg roll. I had horrible luck getting this to print at
Ender 3 Pro: Initial Setup and Recommended Prints : 16 Steps (with Pictures) - Instructables
Is petg notoriously stringy and horrible for small models? I just got my ender 3 V2 for Christmas and a jayo petg roll. I had horrible luck getting this to print at
Ayo this post is like Ziti,PLA, PETG 3D Printing
Is petg notoriously stringy and horrible for small models? I just got my ender 3 V2 for Christmas and a jayo petg roll. I had horrible luck getting this to print at
why so stringy and messy after swapping from pla to petg? : r/ender3
Is petg notoriously stringy and horrible for small models? I just got my ender 3 V2 for Christmas and a jayo petg roll. I had horrible luck getting this to print at
At my wits end for PETG. It always starts out totally fine, then the quality just plummets partway through. Settings in the comments, advice appreciated. : r/ender3
Is petg notoriously stringy and horrible for small models? I just got my ender 3 V2 for Christmas and a jayo petg roll. I had horrible luck getting this to print at
Stringing with PETG, how to prevent it? : r/ender3v2
Is petg notoriously stringy and horrible for small models? I just got my ender 3 V2 for Christmas and a jayo petg roll. I had horrible luck getting this to print at
I'm honestly tired… I just got this printer, and I spent hours trying to get it to print properly, and nothing seems to work. Even looking up videos about bed leveling. Even
Recommandé pour vous
Tu pourrais aussi aimer

© 2014-2024 peterpan.com.pe. Inc. ou ses affiliés.